INSTRUMENT SETUP–ALL MAVOWATT 2XX

INSTRUMENT SETUP – ALL MAVOWATT 2XX
The new MAVOWATT-  series offers both automatic and manual setup methods allowing users to be immediately productive, and to begin monitoring within minutes. Automatic setups are the quickest and easiest way to start monitoring in just a few steps. When connected to an energized circuit, the instrument automatically detects the circuit type, nominal voltage/current and displays them for review. The user can then set the current probe type and start monitoring immediately. The instrument will configure itself using triggers based upon the IEEE 1159 +/-  10% of nominal recommendations. Automatic setups are available for both Power Quality and Demand/Energy.
MAVOWATT200系列澳们威尼斯吴乐城
Wizard setups are also available for the user to have complete control over the instrument’s  setup and triggering. The Wizard setup guides you step-by-step through each setup category. Wizard setup categories are: Probes/Scaling, Wiring Configuration, Nominal/Frequency, Monitoring Mode, Trigger Limits, and Finalize. Each category is randomly accessible and guides the user through the settings available in each setup screen. The instrument will also inform the user of potential setup errors, such as mismatches between the circuit type setting and the circuit type automatically detected.
MAVOWATT200系列澳们威尼斯吴乐城
POWER QUALITY MEASUREMENT FUNCTIONS– ALL MAVOWATT 2XX 
The MAVOWATT 2XX instruments offer the latest in Power Quality, Demand and Energy measurement, and monitoring capabilities. Each model is Class A compliant with IEC61000-4-30:2008 and also supports EN50160:2009, IEEE 1159, IEEE 519, IEEE 1453 and IEEE 1459.

Data Acquisition 
Each MAVOWATT 2XX instrument samples every cycle of each voltage and current channel 512 times. Sampling is gapless, which means each voltage and current cycle is continuously sampled without gaps between cycles. Sampling is controlled by a Phase Locked Loop (PLL) circuit that is referenced to channel L1 (A) by default, with other references available. The PLL automatically adjusts the sampling rate to the power line frequency to ensure the instrument always acquires 512 evenly spaced samples per cycle for every channel. Therefore, any variation in the power line frequency adjusts the sampling rate accordingly. This translates to a sampling rate of 30.72KHz at 60Hz and 25.6KHz at 50Hz. Switchable Anti-Aliasing filters are available for strict compliance with IEC61000-4-30 Class A. Note that switching in such filters may limit the transient response of the instrument. The instrument is Class A compliant with Anti-Aliasing filters switched either on or off.

The data acquired by the above process is digitized by a 16-bit Analog to Digital (A/D) converter and is used as the foundation for all voltage, current and power measurements, and computations that are available in the instrument.  This technique of data acquisition is appropriate for low and medium frequency transients as defined by IEEE1159. At 512 samples per cycle, the time between samples is about 32μs at 60Hz and 39μs at 50Hz, which is adequate to record transient activity on most power systems. The MAVOWATT 270 and MAVOWATT 270 -400 have additional high speed transient circuitry for 1 microsecond transient detection.

 

关于银飞
企业概况
企业荣誉
企业学问
企业环境
员工风采
维修售后
产品中心
温度校验仪
测试仪器
数字压力表
澳们威尼斯吴乐城
功率分析仪器
工业内窥镜
澳们威尼斯吴乐城
压力校验仪
资讯资讯
企业资讯
行业资讯
展会资讯
行业解决方案

专业选型请咨询大家工作人员

全国统一服务热线

0755-83959699
0755-83983899
0755-23964199
0755-23964599

(国内任一地区手机、座机均可拨打)

  • 公众号

  • 微博

  • 电子邮件

版权所有:澳们威尼斯吴乐城 粤ICP备15021421号-3

澳们威尼斯吴乐城供应商哪家好,澳们威尼斯吴乐城品牌推荐,澳们威尼斯吴乐城先容说明,Fluke功率分析仪器价格,数字压力表多少钱

收缩

银飞电子在线客服

  • 销售一部 点击这里给我发消息
  • 销售二部 点击这里给我发消息
  • 销售三部 点击这里给我发消息
  • 0755-83959699
  • 0755-83983899
  • 在线留言
XML 地图 | Sitemap 地图